I don't know if this will help you Don, but I have a color pdf file below if you need it.
I hate electrical.
| Attachments: |
| PilotOdyssey.com http://www.pilotodyssey.com/PO/ |
|
| What is required to wire for a charging system? http://www.pilotodyssey.com/PO/viewtopic.php?f=1&t=17870 |
Page 1 of 1 |
| Author: | Superlite_Don [ Tue Jan 30, 2018 10:14 pm ] |
| Post subject: | What is required to wire for a charging system? |
The guy restoring my car is adding the charging system (I never used one). He does not have an FL350 harness, but has the regulator/rectifier and the charging coil. So I know the yellows goes to the yellows, the green from the alternator to the green on the regulator and also to ground. And the red/white to the + on the battery. But is the black wire on the regulator needed? Just not sure what it does. |
|
| Author: | scpilot66 [ Tue Jan 30, 2018 10:33 pm ] |
| Post subject: | Re: What is required to wire for a charging system? |
I would need to check the manual but from memory I think that is the key on power wire. I can check here in a bit if needed. |
|
| Author: | Superlite_Don [ Tue Jan 30, 2018 10:57 pm ] |
| Post subject: | Re: What is required to wire for a charging system? |
That is what it looks like. Is it needed for the charging system to work correctly? Does that mean it just gets switched +12V? I appreciate the help when you get the chance. Don |
|
| Author: | scpilot66 [ Tue Jan 30, 2018 11:31 pm ] |
| Post subject: | Re: What is required to wire for a charging system? |
OK just checked, yes black is key on power +12v and yes you need it. Do not leave the black wire powered all the time, a toggle switch is fine if you do not have an ignition switch. On your red/white wire be sure to run a 15 amp fuse inline. Good luck, Steve. |
|
| Author: | canadian oddy [ Tue Jan 30, 2018 11:34 pm ] | ||
| Post subject: | Re: What is required to wire for a charging system? | ||
I don't know if this will help you Don, but I have a color pdf file below if you need it. I hate electrical.
|
|||
| Author: | canadian oddy [ Tue Jan 30, 2018 11:58 pm ] | ||
| Post subject: | Re: What is required to wire for a charging system? | ||
I think this next pdf answers your question. It is a Honda color code explanation. It's for small motorcycles but I don't see why it wouldn't be the same for the atv's
|
|||
| Author: | Superlite_Don [ Wed Jan 31, 2018 10:17 pm ] |
| Post subject: | Re: What is required to wire for a charging system? |
Great. You guys are the best. |
|
| Author: | Garemie [ Sat Sep 01, 2018 12:14 pm ] |
| Post subject: | Re: What is required to wire for a charging system? |
scpilot66 wrote: OK just checked, yes black is key on power +12v and yes you need it. Do not leave the black wire powered all the time, a toggle switch is fine if you do not have an ignition switch. On your red/white wire be sure to run a 15 amp fuse inline. Good luck, Steve. Sorry to resurrect, but can someone explain this? I leave my ignition switch on all the time on my 350s, does this have some negative effect? I have never seen it drain the battery...yet.... |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|
