Board index

My Home Page

PilotOdyssey.com By hoser...


PilotOdyssey.com Chat Room

PilotOdyssey.com Photo Album

* Login   * Register * FAQ
http://www.pilotodyssey.com/PO/adm/images/imagemenu/smiley_cool.png PilotOdyssey.com Chat    http://www.pilotodyssey.com/PO/adm/images/imagemenu/find.png PilotOdyssey.com Google Search    http://www.pilotodyssey.com/PO/adm/images/imagemenu/emoticon_tongue.png FL400 Parts    http://www.pilotodyssey.com/PO/adm/images/imagemenu/emoticon_grin.png FL350 Parts    http://www.pilotodyssey.com/PO/adm/images/imagemenu/emoticon_evilgrin.png FL250 Parts    http://www.pilotodyssey.com/PO/adm/images/imagemenu/emoticon_unhappy.png Admin Email   
It is currently Thu Mar 28, 2024 2:11 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 7 posts ] 
Author Message
PostPosted: Wed Mar 30, 2011 8:42 am 
Offline

Joined: Sat Jun 30, 2007 7:45 am
Posts: 1040
Location: hole above ground
Hello need info on this spacer or Collar

need od id and height so I can make one for cafercr35

I'm rebuilding his rear knuckle


this is Item #1

Image

thanks Speed


Top
 Profile  
 
PostPosted: Wed Mar 30, 2011 9:11 am 
Offline

Joined: Mon Dec 15, 2003 2:40 pm
Posts: 22512
Location: Chicago
Probably have to take apart the other side that is still good and measure it?

wouldn't the distance spacer for the inner race be the same as the distance between the outer race that is machined into the hub itself so their was no stress on your balls when you tighten the axle nut?

Check with Mudbogger he probably has one in stock he can measure.

Stoneman has one that is off his basket case Pilot and apart?


Top
 Profile E-mail  
 
PostPosted: Wed Mar 30, 2011 9:40 am 
Offline

Joined: Sat Jun 30, 2007 7:45 am
Posts: 1040
Location: hole above ground
hoser wrote:
Probably have to take apart the other side that is still good and measure it?

wouldn't the distance spacer for the inner race be the same as the distance between the outer race that is machined into the hub itself so their was no stress on your balls when you tighten the axle nut?

Check with Mudbogger he probably has one in stock he can measure.

Stoneman has one that is off his basket case Pilot and apart?


from my numbers I get max of
OD 43mm (1.6928)
ID 35mm + (1.3779+)
24mm tall (.9449) this the number that matters height

Knuckle 68mm wide over all
bore on each side 24mm deep
bearing 14mm wide
seal 8 mm wide ?
this leave me with 20mm in the center of hosing

Thank you for your time
SpeedChaser


Top
 Profile  
 
PostPosted: Wed Mar 30, 2011 11:03 am 
Offline

Joined: Tue Dec 16, 2003 2:45 pm
Posts: 885
I have new spacer and a knuckle in need of repair.
PM me your mailing address asap and it will go out today.


Top
 Profile  
 
PostPosted: Wed Mar 30, 2011 1:25 pm 
Offline

Joined: Sat Jun 30, 2007 7:45 am
Posts: 1040
Location: hole above ground
Stoneman wrote:
I have new spacer and a knuckle in need of repair.
PM me your mailing address asap and it will go out today.


You got Mail

thanks Speed


Top
 Profile  
 
PostPosted: Wed Mar 30, 2011 3:39 pm 
Offline

Joined: Tue Oct 18, 2005 6:15 pm
Posts: 631
Location: Fredon,NJ
Thanks Speed.
PS - dust covers still haven't shipped from Service Honda....they estimate by Friday.


Thanks Stoneman


Top
 Profile  
 
PostPosted: Fri Apr 01, 2011 11:34 am 
Offline

Joined: Sat Jun 30, 2007 7:45 am
Posts: 1040
Location: hole above ground
speedchaser wrote:
hoser wrote:
Probably have to take apart the other side that is still good and measure it?

wouldn't the distance spacer for the inner race be the same as the distance between the outer race that is machined into the hub itself so their was no stress on your balls when you tighten the axle nut?

Check with Mudbogger he probably has one in stock he can measure.

Stoneman has one that is off his basket case Pilot and apart?


from my numbers I get max of
OD 43mm (1.6928)
ID 35mm + (1.3779+)
24mm tall (.9449) this the number that matters height

Knuckle 68mm wide over all
bore on each side 24mm deep
bearing 14mm wide
seal 8 mm wide ?
this leave me with 20mm in the center of hosing

Thank you for your time
SpeedChaser




spacer is
1.677 od x 1.431 id x .789 tall this what the Honda part measures up as




Thank you stoneman
:-)


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Registered users: Bing [Bot], Google [Bot], Lanix


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group