Hello need info on this spacer or Collar
need od id and height so I can make one for cafercr35
I'm rebuilding his rear knuckle
this is Item #1
thanks Speed
| PilotOdyssey.com http://www.pilotodyssey.com/PO/ |
|
| Need info on fl400 42621-HE0-000 Collar, Rr. Axle http://www.pilotodyssey.com/PO/viewtopic.php?f=106&t=9044 |
Page 1 of 1 |
| Author: | speedchaser [ Wed Mar 30, 2011 8:42 am ] |
| Post subject: | Need info on fl400 42621-HE0-000 Collar, Rr. Axle |
Hello need info on this spacer or Collar need od id and height so I can make one for cafercr35 I'm rebuilding his rear knuckle this is Item #1 thanks Speed |
|
| Author: | hoser [ Wed Mar 30, 2011 9:11 am ] |
| Post subject: | Re: Need info on fl400 42621-HE0-000 Collar, Rr. Axle |
Probably have to take apart the other side that is still good and measure it? wouldn't the distance spacer for the inner race be the same as the distance between the outer race that is machined into the hub itself so their was no stress on your balls when you tighten the axle nut? Check with Mudbogger he probably has one in stock he can measure. Stoneman has one that is off his basket case Pilot and apart? |
|
| Author: | speedchaser [ Wed Mar 30, 2011 9:40 am ] |
| Post subject: | Re: Need info on fl400 42621-HE0-000 Collar, Rr. Axle |
hoser wrote: Probably have to take apart the other side that is still good and measure it? wouldn't the distance spacer for the inner race be the same as the distance between the outer race that is machined into the hub itself so their was no stress on your balls when you tighten the axle nut? Check with Mudbogger he probably has one in stock he can measure. Stoneman has one that is off his basket case Pilot and apart? from my numbers I get max of OD 43mm (1.6928) ID 35mm + (1.3779+) 24mm tall (.9449) this the number that matters height Knuckle 68mm wide over all bore on each side 24mm deep bearing 14mm wide seal 8 mm wide ? this leave me with 20mm in the center of hosing Thank you for your time SpeedChaser |
|
| Author: | Stoneman [ Wed Mar 30, 2011 11:03 am ] |
| Post subject: | Re: Need info on fl400 42621-HE0-000 Collar, Rr. Axle |
I have new spacer and a knuckle in need of repair. PM me your mailing address asap and it will go out today. |
|
| Author: | speedchaser [ Wed Mar 30, 2011 1:25 pm ] |
| Post subject: | Re: Need info on fl400 42621-HE0-000 Collar, Rr. Axle |
Stoneman wrote: I have new spacer and a knuckle in need of repair. PM me your mailing address asap and it will go out today. You got Mail thanks Speed |
|
| Author: | cafercr35 [ Wed Mar 30, 2011 3:39 pm ] |
| Post subject: | Re: Need info on fl400 42621-HE0-000 Collar, Rr. Axle |
Thanks Speed. PS - dust covers still haven't shipped from Service Honda....they estimate by Friday. Thanks Stoneman |
|
| Author: | speedchaser [ Fri Apr 01, 2011 11:34 am ] |
| Post subject: | Re: Need info on fl400 42621-HE0-000 Collar, Rr. Axle |
speedchaser wrote: hoser wrote: Probably have to take apart the other side that is still good and measure it? wouldn't the distance spacer for the inner race be the same as the distance between the outer race that is machined into the hub itself so their was no stress on your balls when you tighten the axle nut? Check with Mudbogger he probably has one in stock he can measure. Stoneman has one that is off his basket case Pilot and apart? from my numbers I get max of OD 43mm (1.6928) ID 35mm + (1.3779+) 24mm tall (.9449) this the number that matters height Knuckle 68mm wide over all bore on each side 24mm deep bearing 14mm wide seal 8 mm wide ? this leave me with 20mm in the center of hosing Thank you for your time SpeedChaser spacer is 1.677 od x 1.431 id x .789 tall this what the Honda part measures up as Thank you stoneman 
|
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|