PilotOdyssey.com
http://www.pilotodyssey.com/PO/

81-84 ATC250R Evilbay Engine
http://www.pilotodyssey.com/PO/viewtopic.php?f=45&t=4065
Page 1 of 1

Author:  hoser [ Wed Mar 12, 2008 6:57 pm ]
Post subject:  81-84 ATC250R Evilbay Engine

I picked up a 81-84 Engine off ebay since it went cheap, just got it in the mail today, I really don't have time for another project but could not pass it up.

At a first look the cases all look undamaged, it looks like its never had a chain break and hit the cases, the shift lever shaft has had a shifter welded to it at one time or another so the shaft will need replaced.

When get some time I will split the cases and see if its rebuildable, the rod is lose so I know it needs another rod or crank, normally I would just shelf this and rebuild if I ever need it but replacement parts I am sure are getting harder to find so I guess I better split the cases and see what it needs and find parts ASAP, I can rebuild then box up and put it on the shelf.

I removed the clutch cover and discovered someone replaced the O ring used to seal the cover with silicone haha

The guy complained he lost money on shipping... why would you ship the Engine with the oil in it?

http://cgi.ebay.com/ebaymotors/ws/eBayI ... OTORS:1123

Attachments:
DSC02126.JPG
DSC02126.JPG [ 69.67 KiB | Viewed 945 times ]
DSC02128.JPG
DSC02128.JPG [ 46.13 KiB | Viewed 944 times ]
DSC02129.JPG
DSC02129.JPG [ 85.53 KiB | Viewed 944 times ]

Author:  hoser [ Wed Mar 12, 2008 6:59 pm ]
Post subject: 

No chain damage.

Lots of miss matched case bolts.

Attachments:
DSC02134.JPG
DSC02134.JPG [ 83.49 KiB | Viewed 943 times ]

Author:  hoser [ Wed Mar 12, 2008 7:01 pm ]
Post subject: 

This Engine has an internal balancer like the Pilot and 350 Ody, case looks good.

Attachments:
DSC02135.JPG
DSC02135.JPG [ 55.01 KiB | Viewed 942 times ]

Author:  hoser [ Wed Mar 12, 2008 7:02 pm ]
Post subject: 

More case pics

Attachments:
DSC02136.JPG
DSC02136.JPG [ 79.18 KiB | Viewed 941 times ]

Author:  hoser [ Wed Mar 12, 2008 7:03 pm ]
Post subject: 

Under flywheel cover is the usual rust.

Red paint on Engine means it is a 81-82

Attachments:
DSC02137.JPG
DSC02137.JPG [ 95.3 KiB | Viewed 939 times ]
DSC02138.JPG
DSC02138.JPG [ 97.35 KiB | Viewed 939 times ]
DSC02139.JPG
DSC02139.JPG [ 96.32 KiB | Viewed 939 times ]
DSC02141.JPG
DSC02141.JPG [ 79.18 KiB | Viewed 939 times ]

Author:  hoser [ Wed Mar 12, 2008 7:06 pm ]
Post subject: 

Flywheel pulled right off using the right puller.

Normal rust inside, that light layer of rust is just enough to make a no spark condition, clean it up and install presto spark again.

Attachments:
DSC02144.JPG
DSC02144.JPG [ 76.23 KiB | Viewed 937 times ]
DSC02145.JPG
DSC02145.JPG [ 77.85 KiB | Viewed 937 times ]
DSC02148.JPG
DSC02148.JPG [ 105.19 KiB | Viewed 937 times ]
DSC02149.JPG
DSC02149.JPG [ 101.39 KiB | Viewed 937 times ]
File comment: I don't think anything below the flywheel has been apart before.
DSC02150.JPG
DSC02150.JPG [ 95.75 KiB | Viewed 937 times ]

Author:  hoser [ Wed Mar 12, 2008 7:07 pm ]
Post subject: 

Drain bolt, the aluminum gasket is way beyond its useful life, this Engine has seen many oil changes hopefully it looks like it when I split the cases too heh :shock:

Attachments:
DSC02151.JPG
DSC02151.JPG [ 67.96 KiB | Viewed 936 times ]
DSC02155.JPG
DSC02155.JPG [ 41.77 KiB | Viewed 936 times ]

Author:  hoser [ Wed Mar 12, 2008 7:08 pm ]
Post subject: 

More over all pics

Attachments:
DSC02156.JPG
DSC02156.JPG [ 87.73 KiB | Viewed 934 times ]
DSC02157.JPG
DSC02157.JPG [ 84.44 KiB | Viewed 934 times ]
File comment: Rust on the crank
DSC02158.JPG
DSC02158.JPG [ 88.16 KiB | Viewed 934 times ]
DSC02160.JPG
DSC02160.JPG [ 82.36 KiB | Viewed 934 times ]

Author:  Ody_Stable [ Wed Mar 12, 2008 8:32 pm ]
Post subject: 

Nice.

Hopefully the insides are as good and clean as you're hoping they are.

I have yet to crack into the complete '84 Engine I got with the 300R kit, the original black paint is still in great shape though so hopefully it's in decent condition, but like yours, it was cheap and I couldn't pass it up.

Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/