Board index

My Home Page

PilotOdyssey.com By hoser...


PilotOdyssey.com Chat Room

PilotOdyssey.com Photo Album

* Login   * Register * FAQ
http://www.pilotodyssey.com/PO/adm/images/imagemenu/smiley_cool.png PilotOdyssey.com Chat    http://www.pilotodyssey.com/PO/adm/images/imagemenu/find.png PilotOdyssey.com Google Search    http://www.pilotodyssey.com/PO/adm/images/imagemenu/emoticon_tongue.png FL400 Parts    http://www.pilotodyssey.com/PO/adm/images/imagemenu/emoticon_grin.png FL350 Parts    http://www.pilotodyssey.com/PO/adm/images/imagemenu/emoticon_evilgrin.png FL250 Parts    http://www.pilotodyssey.com/PO/adm/images/imagemenu/emoticon_unhappy.png Admin Email    http://www.pilotodyssey.com/PO/adm/images/imagemenu/emoticon_grin.png PilotOdyssey.com V2.0   
It is currently Wed Feb 21, 2018 2:46 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 17 posts ] 
Author Message
PostPosted: Wed Mar 05, 2008 9:21 pm 
Offline

Joined: Sat Jun 30, 2007 7:45 am
Posts: 1028
Location: hole above ground
Hello
Well found a Exhaust Pipe / Tubing Bender
That had my name on it. At $600
It was in a fire and got smoked
Me and the wife picked it up late last Friday
Man did it ever smell.
Me and my son at the age of 10 tore in all down and
Started to sandblast all the part that fit in the cabinet
Well the kid lasted a whole 20 min on the sandblaster
That he wanted to use so bad. So I finished up today 4 days later
And here are some picks
Thanks For Looking
Speedchaser


Attachments:
File comment: The MC-59 from Ben Pearson is truly the ultimate in pipe bender technology. Incorporating state-of-the-art technology, the MC-59 pipe bender leads the industry in operator convenience features --- 180 degree bend on 5" radius, 3" bending capabil
mc59.jpg
mc59.jpg [ 23.69 KiB | Viewed 2015 times ]
File comment: main beam
MVC-529X.JPG
MVC-529X.JPG [ 102.72 KiB | Viewed 2015 times ]
File comment: pivot arms
MVC-530X.JPG
MVC-530X.JPG [ 109.14 KiB | Viewed 2015 times ]
File comment: bottom tray and tank
MVC-531X.JPG
MVC-531X.JPG [ 123.33 KiB | Viewed 1577 times ]
File comment: cylinders and pump
MVC-532X.JPG
MVC-532X.JPG [ 102 KiB | Viewed 2015 times ]
Top
 Profile  
 
 Post subject:
PostPosted: Wed Mar 05, 2008 9:31 pm 
Offline

Joined: Sat Jun 30, 2007 7:45 am
Posts: 1028
Location: hole above ground
next


Attachments:
File comment: side shelfs
MVC-535X.JPG
MVC-535X.JPG [ 77.08 KiB | Viewed 2012 times ]
File comment: the smoked motor (( Internal Combustion Engine ? ))
MVC-536X.JPG
MVC-536X.JPG [ 84.12 KiB | Viewed 2012 times ]
File comment: some of the tooling
MVC-537X.JPG
MVC-537X.JPG [ 110.09 KiB | Viewed 2012 times ]
File comment: sandblasting cab
MVC-540X.JPG
MVC-540X.JPG [ 110.45 KiB | Viewed 2012 times ]
File comment: the pile of sand blasted parts
wow lot of work there

MVC-545X.JPG
MVC-545X.JPG [ 102.79 KiB | Viewed 2012 times ]
Top
 Profile  
 
 Post subject:
PostPosted: Wed Mar 05, 2008 9:32 pm 
Offline

Joined: Mon Dec 15, 2003 2:40 pm
Posts: 22133
Location: Chicago
Looks like a real project, do you think it will work again soon ?


Top
 Profile E-mail  
 
 Post subject:
PostPosted: Wed Mar 05, 2008 9:40 pm 
Offline

Joined: Sat Jun 30, 2007 7:45 am
Posts: 1028
Location: hole above ground
next


Attachments:
File comment: Here you go csi the main valve and relief valve
MVC-546X.JPG
MVC-546X.JPG [ 109.14 KiB | Viewed 2009 times ]
File comment: bottom bent a half of a inch
MVC-551X.JPG
MVC-551X.JPG [ 94.89 KiB | Viewed 2009 times ]
File comment: last one for the day trying to get the *anm thing flat
MVC-553X.JPG
MVC-553X.JPG [ 90.21 KiB | Viewed 2009 times ]
Top
 Profile  
 
 Post subject:
PostPosted: Mon Mar 10, 2008 12:59 pm 
Offline

Joined: Sat Jun 30, 2007 7:45 am
Posts: 1028
Location: hole above ground
next
short mov of tank in lathe
http://www.youtube.com/watch?v=4dXXnp0JJsc

thanks for looking
Speedchaser


Attachments:
File comment: welded some extra angle on bottom
MVC-556X.JPG
MVC-556X.JPG [ 100.61 KiB | Viewed 1931 times ]
File comment: primed with zinc
MVC-557X.JPG
MVC-557X.JPG [ 102.74 KiB | Viewed 1931 times ]
File comment: weld tubing on tank so I can put in lathe to clean all burnt rust out
MVC-559X.JPG
MVC-559X.JPG [ 112.23 KiB | Viewed 1931 times ]
File comment: close up
MVC-560X.JPG
MVC-560X.JPG [ 87.43 KiB | Viewed 1931 times ]
File comment: in lathe with a hand full 5/8" nuts and diesel fuel
Short mov. http://www.youtube.com/watch?v=4dXXnp0JJsc

MVC-561X.JPG
MVC-561X.JPG [ 108.96 KiB | Viewed 1931 times ]
File comment: some assembly and little paint
MVC-564X.JPG
MVC-564X.JPG [ 84.62 KiB | Viewed 1931 times ]
Top
 Profile  
 
 Post subject:
PostPosted: Sun Mar 16, 2008 8:57 pm 
Offline

Joined: Sat Jun 30, 2007 7:45 am
Posts: 1028
Location: hole above ground
Well got more done this weekend more paint too
thanks for looking
speedchaser


Attachments:
File comment: more assembly new used motor (( Internal Combustion Engine ? )) updated to 3ph 5hp
MVC-583X.JPG
MVC-583X.JPG [ 82.44 KiB | Viewed 1905 times ]
File comment: sand blasted cylinders and some painted bend tools
MVC-585X.JPG
MVC-585X.JPG [ 76.55 KiB | Viewed 1905 times ]
File comment: kid out playing in mud with snowsuit
on

MVC-589X.JPG
MVC-589X.JPG [ 82.53 KiB | Viewed 1905 times ]
File comment: color coded tooling pre size
MVC-590X.JPG
MVC-590X.JPG [ 81.08 KiB | Viewed 1905 times ]
File comment: side veiw last pic for today
thanks for looking

MVC-591X.JPG
MVC-591X.JPG [ 72.78 KiB | Viewed 1905 times ]
Top
 Profile  
 
 Post subject:
PostPosted: Tue Mar 18, 2008 1:36 am 
Offline

Joined: Fri Jan 11, 2008 1:25 am
Posts: 93
Location: South Gate
What are your plans with this machine do you have your own shop? Or is just for your own use. I just paid 20 bucks to have a spark arrestor adapted to my dg exhaust and they used a machine that looked just like that one.


Top
 Profile E-mail  
 
 Post subject:
PostPosted: Tue Mar 18, 2008 10:50 am 
Offline

Joined: Wed Dec 17, 2003 8:43 pm
Posts: 1368
Location: Colorado
Yeah, I've been curious also. That looks like serious machinery, can't wait to see what you make with it.


Top
 Profile  
 
 Post subject:
PostPosted: Tue Mar 25, 2008 10:14 pm 
Offline

Joined: Sat Jun 30, 2007 7:45 am
Posts: 1028
Location: hole above ground
Hello I do have my own shop witch I do prototype furniture parts.
I had been looking for this type of bender to do other then guts round tube.
It great that it has the dies that go from 1-1/2 to 3” round
I think that my neighbor has his mind going all over the place with ideas.
And as my son gets older I will be getting back in mud bogging. And doing my own frames, bumpers, side bars and roll cages ext


Know back to work found one cylinder end cap with broken ear witch is cast iron
And main top cylinder the rod looked like they took a hammer to it. So I made a new
one. Here are sum more pic’s


Thanks for looking
speedchaser


Attachments:
File comment: time to pre heat the cast iron to aprox 900 F
MVC-598X.JPG
MVC-598X.JPG [ 79 KiB | Viewed 1826 times ]
File comment: getting hot. Tip for the day your spit will bounce off the hot steel at 600F see old cylinder rod in back ground some one got happy with a hammer
MVC-600X.JPG
MVC-600X.JPG [ 110.02 KiB | Viewed 1826 times ]
File comment: weld up
MVC-604X.JPG
MVC-604X.JPG [ 98.4 KiB | Viewed 1826 times ]
File comment: other side
MVC-605X.JPG
MVC-605X.JPG [ 100.96 KiB | Viewed 1826 times ]
File comment: went and added a washer to the top
to help support the load

MVC-602X.JPG
MVC-602X.JPG [ 112.54 KiB | Viewed 1826 times ]
File comment: all done welding
MVC-606X.JPG
MVC-606X.JPG [ 117.67 KiB | Viewed 1577 times ]
Top
 Profile  
 
 Post subject:
PostPosted: Tue Mar 25, 2008 10:23 pm 
Offline

Joined: Sat Jun 30, 2007 7:45 am
Posts: 1028
Location: hole above ground
next
The rest of the cylinders and pump where all rebuild able with new seals
The two manual valves needed seals and handles the handles melted off


Attachments:
File comment: bottom side of cap cleaned up in lathe
MVC-608X.JPG
MVC-608X.JPG [ 104.65 KiB | Viewed 1823 times ]
File comment: new machined rod 2" dia x 23" long
MVC-609X.JPG
MVC-609X.JPG [ 107.51 KiB | Viewed 1823 times ]
File comment: threaded end 1-1/4-12 thread
MVC-610X.JPG
MVC-610X.JPG [ 100.51 KiB | Viewed 1823 times ]
Top
 Profile  
 
 Post subject:
PostPosted: Wed Mar 26, 2008 5:22 pm 
Offline

Joined: Mon Dec 15, 2003 2:40 pm
Posts: 22133
Location: Chicago
Nice work!

Almost done?


Top
 Profile E-mail  
 
 Post subject:
PostPosted: Sat Apr 05, 2008 9:14 pm 
Offline

Joined: Sat Jun 30, 2007 7:45 am
Posts: 1028
Location: hole above ground
all the paint done today fist nice day to paint out side
:-)


Attachments:
MVC-618X.JPG
MVC-618X.JPG [ 104.46 KiB | Viewed 1768 times ]
MVC-619X.JPG
MVC-619X.JPG [ 76.04 KiB | Viewed 1768 times ]
MVC-620X.JPG
MVC-620X.JPG [ 84.05 KiB | Viewed 1768 times ]
MVC-611X.JPG
MVC-611X.JPG [ 84.08 KiB | Viewed 1768 times ]
MVC-612X.JPG
MVC-612X.JPG [ 105.12 KiB | Viewed 1768 times ]
Top
 Profile  
 
 Post subject:
PostPosted: Thu Apr 17, 2008 6:04 pm 
Offline

Joined: Sat Jun 30, 2007 7:45 am
Posts: 1028
Location: hole above ground
Getting close on finishing this project up
Assembly time And time to make new hoses


Attachments:
File comment: SOME Assembly
MVC-622X.JPG
MVC-622X.JPG [ 105.91 KiB | Viewed 1697 times ]
File comment: more
MVC-624X.JPG
MVC-624X.JPG [ 116.48 KiB | Viewed 1697 times ]
File comment: mount motor (( Internal Combustion Engine ? ))
MVC-646X.JPG
MVC-646X.JPG [ 107.75 KiB | Viewed 1697 times ]
File comment: hose time pluming
MVC-647X.JPG
MVC-647X.JPG [ 99.76 KiB | Viewed 1697 times ]
File comment: gage pressure relief
MVC-650X.JPG
MVC-650X.JPG [ 83.2 KiB | Viewed 1697 times ]
File comment: more
MVC-651X.JPG
MVC-651X.JPG [ 101.73 KiB | Viewed 1697 times ]
Top
 Profile  
 
 Post subject:
PostPosted: Thu Apr 17, 2008 6:14 pm 
Offline

Joined: Sat Jun 30, 2007 7:45 am
Posts: 1028
Location: hole above ground
hose crimper and last pic for the pluming
next Electric panel wiring


thanks for looking SpeedChaser


Attachments:
File comment: crimper hose
MVC-652X.JPG
MVC-652X.JPG [ 76.12 KiB | Viewed 1696 times ]
File comment: last pic for the day thanks for looking SpeedChaser
MVC-653X.JPG
MVC-653X.JPG [ 94.63 KiB | Viewed 1696 times ]
Top
 Profile  
 
 Post subject:
PostPosted: Thu Apr 17, 2008 7:05 pm 
Offline

Joined: Mon Dec 15, 2003 2:40 pm
Posts: 22133
Location: Chicago
Looking good how long before you bend pipe?


Top
 Profile E-mail  
 
 Post subject:
PostPosted: Sun Oct 12, 2008 8:03 pm 
Offline

Joined: Sat Jun 30, 2007 7:45 am
Posts: 1028
Location: hole above ground
well I finished up the bender last week
all in all things went very well bender is like new

Today Made some new tooling so I can bend 1-1/4" tube
see pic's

thank for looking
SpeedChaser


Attachments:
File comment: cut out side shape and pocket
MVC-836X.JPG
MVC-836X.JPG [ 77.36 KiB | Viewed 1645 times ]
File comment: that block is from the furnace project
poured from melted 6061 scrap

MVC-837X.JPG
MVC-837X.JPG [ 92.07 KiB | Viewed 1645 times ]
File comment: cut radius in side
MVC-838X.JPG
MVC-838X.JPG [ 87.54 KiB | Viewed 1645 times ]
File comment: all fitted in bender with slider blocks
MVC-840X.JPG
MVC-840X.JPG [ 110.31 KiB | Viewed 1645 times ]
Top
 Profile  
 
 Post subject:
PostPosted: Mon Nov 17, 2008 4:26 pm 
Offline

Joined: Mon Dec 15, 2003 2:40 pm
Posts: 22133
Location: Chicago
Any updates here?


Top
 Profile E-mail  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 17 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Registered users: Baidu [Spider], Bing [Bot], dradford85, FloridaEdd, GAPILOT, Google [Bot], jknarfal, liduno, mykxp, Pilotman, Q, rmesser, Rppjr, toby, Yahoo [Bot]


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group