PilotOdyssey.com
http://www.pilotodyssey.com/PO/

fl350 stock head cc's
http://www.pilotodyssey.com/PO/viewtopic.php?f=46&t=6747		 Page 1 of 1
Author:  speedchaser [ Thu Feb 18, 2010 6:42 pm ]
Post subject:  fl350 stock head cc's
Hello today I'm cc a stock fl350 head and in a new thread will be Measuring the stock combustion chamber


thanks For looking
SpeedChaser

Attachments:
File comment: getting read to cc stock fl350 head
MVC-233X.JPG
MVC-233X.JPG [ 89.53 KiB | Viewed 5699 times ]
MVC-234X.JPG [102.56 KiB]
Downloaded 142 times
File comment: first drill feed hole and two vents
supper glue plex to top of head
MVC-236X.JPG [93.54 KiB]
Downloaded 142 times
File comment: glue down and put weight on top and let sit
MVC-237X.JPG [108.39 KiB]
Downloaded 142 times
File comment: I used hydraulic or air tool oil light weight aw 10 20
MVC-248X.JPG
MVC-248X.JPG [ 104.06 KiB | Viewed 5699 times ]
File comment: I come up with approx 36cc's
MVC-250X.JPG [39.05 KiB]
Downloaded 142 times
Author:  hoser [ Thu Feb 18, 2010 7:57 pm ]
Post subject: 
Nice...

You can put a light coat of grease or Vaseline on the head where the head gasket goes to seal the Plexiglas to the head, I use water but their is nothing wrong with using oil either..
Author:  adnoh [ Sat Feb 20, 2010 12:12 pm ]
Post subject: 
Was that a straight or curved fin head. I logged the data: stock head 36 cc total head, Cumbustion chamber ?
Author:  speedchaser [ Sat Feb 20, 2010 2:56 pm ]
Post subject: 
adnoh wrote:
Was that a straight or curved fin head. I logged the data: stock head 36 cc total head, Cumbustion chamber ?



Adnoh curved fin head with spark pug and fig with out head gaskets

thanks Speed


:shock:
Author:  speedchaser [ Sat Feb 20, 2010 2:59 pm ]
Post subject: 
Note to Me don't let sit over night with super glue on it dose bond very well
need hammer and chisel to remove :-)

Speedchaser
Author:  adnoh [ Sat Feb 20, 2010 4:03 pm ]
Post subject: 
Updated:

I logged the data: (curved)stock head ( with spark plug no gasket)36 cc total head.

Thanks again speedchaser.
Author:  mudbogger [ Sun Feb 21, 2010 9:15 am ]
Post subject: 
Hey Hoser, what did TPREED'S afterthought head cc, when I purchased that years ago he had told me it was a larger diameter head-was curious on that.
Author:  Turbotexas [ Sun Feb 21, 2010 10:45 pm ]
Post subject: 
speedchaser wrote:
Note to Me don't let sit over night with super glue on it dose bond very well
need hammer and chisel to remove :-)

Speedchaser


That is too funny!!!
Author:  stix [ Sun Feb 21, 2010 11:20 pm ]
Post subject: 
Hey Speed. I went back through my old notes, and found that i also came up with 36ml for the Honda curved finned head with the plug installed. I also measured a Rand knock off cool head and it measured 38ml.
Author:  Tpreed [ Sun Feb 21, 2010 11:29 pm ]
Post subject: 
Mudbogger wrote:
Hey Hoser, what did TPREED'S afterthought head cc, when I purchased that years ago he had told me it was a larger diameter head-was curious on that.

i believe i got 37cc.. probably messed up the measurement tho LOL
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/