Board index

My Home Page

PilotOdyssey.com By hoser...


PilotOdyssey.com Chat Room

PilotOdyssey.com Photo Album

* Login   * Register * FAQ
http://www.pilotodyssey.com/PO/adm/images/imagemenu/smiley_cool.png PilotOdyssey.com Chat    http://www.pilotodyssey.com/PO/adm/images/imagemenu/find.png PilotOdyssey.com Google Search    http://www.pilotodyssey.com/PO/adm/images/imagemenu/emoticon_tongue.png FL400 Parts    http://www.pilotodyssey.com/PO/adm/images/imagemenu/emoticon_grin.png FL350 Parts    http://www.pilotodyssey.com/PO/adm/images/imagemenu/emoticon_evilgrin.png FL250 Parts    http://www.pilotodyssey.com/PO/adm/images/imagemenu/emoticon_unhappy.png Admin Email   
It is currently Thu Mar 28, 2024 11:00 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 84 posts ]  Go to page Previous  1, 2, 3, 4
Author Message
PostPosted: Mon May 29, 2017 10:00 pm 
Offline

Joined: Wed Jan 14, 2009 2:10 am
Posts: 4678
Location: Carson City NV
As far as blowing into it with just lung pressure the best you're going to do is a bout 1 psi, however your fuel pressure from the pump is going to be around 3 to 5 psi so you can't match the pressure of the pump with your lungs.

You could have a dirty fuel seat. Remove the carb, take the carb bowl off, remove the float and fuel valve then polish the valve seat and the valve plunger by using some polishing compound on the end of a Q-Tip shoved inside a drill.

Rand


Top
 Profile E-mail  
 
PostPosted: Mon May 29, 2017 10:49 pm 
Offline

Joined: Mon Oct 25, 2004 10:02 am
Posts: 2865
Location: East Peoria IL
Don't do this.

https://m.youtube.com/watch?v=zUObiYd64kw

I think you can find anything on YouTube.


Top
 Profile E-mail  
 
PostPosted: Mon May 29, 2017 11:20 pm 
Offline

Joined: Mon Nov 21, 2016 12:31 am
Posts: 144
Thanks, I had checked that. It is solid. still leaking so I'm guessing perhaps the needle is just not able to seal any more. Its running good now.


Top
 Profile E-mail  
 
PostPosted: Mon May 29, 2017 11:23 pm 
Offline

Joined: Mon Oct 25, 2004 10:02 am
Posts: 2865
Location: East Peoria IL
Randman wrote:
As far as blowing into it with just lung pressure the best you're going to do is a bout 1 psi, however your fuel pressure from the pump is going to be around 3 to 5 psi so you can't match the pressure of the pump with your lungs.

You could have a dirty fuel seat. Remove the carb, take the carb bowl off, remove the float and fuel valve then polish the valve seat and the valve plunger by using some polishing compound on the end of a Q-Tip shoved inside a drill.

Rand


Ya know back in the day, mid 80s, I knew a girl who had a set of lungs that could easily blow 3 to 5 pounds per square inch. Aaaaaaaahhhhhh the good old days. :shock:


Top
 Profile E-mail  
 
PostPosted: Tue May 30, 2017 12:16 am 
Offline

Joined: Wed Jan 14, 2009 2:10 am
Posts: 4678
Location: Carson City NV
ROFLMAO!!!!!!!!!!!!!! :-)

You knew my old girlfriend too?

Rand


Top
 Profile E-mail  
 
PostPosted: Sun Jun 04, 2017 11:37 am 
Offline

Joined: Mon Nov 21, 2016 12:31 am
Posts: 144
Well its almost done. just a few small details. I drove it around the yard but it never did get warmed up enough to have any power to speak of unless the carb is the issue. It fires right up. I still need the police to come do a vin check before i can complete the mounting of the rad.


Top
 Profile E-mail  
 
PostPosted: Thu Oct 11, 2018 9:30 am 
Offline

Joined: Mon Nov 21, 2016 12:31 am
Posts: 144
Image

Starting with the bottom section where the springs go. 1 springs, 2 plastic, 3 gasket, middle section, 4 gasket, 5 plastic, 6 gasket and top of pump. does 7 get used or does it go on each side of #2? i was thinking not only due to the need for the plastic to be flat to seal on the spring section.


Top
 Profile E-mail  
 
PostPosted: Thu Oct 11, 2018 1:55 pm 
Offline

Joined: Tue Jan 17, 2012 3:19 am
Posts: 7698
Location: Hope, B.C Canada
rmesser wrote:
Ya know back in the day, mid 80s, I knew a girl who had a set of lungs that could easily blow 3 to 5 pounds per square inch. Aaaaaaaahhhhhh the good old days. :shock:


Watch it !!!!!!
That was over 30yrs ago, so it should be just about time for the Democrats and all your old girl friends to come out of the wood work and accuse you of grabbing them by the P___Y.


Top
 Profile E-mail  
 
PostPosted: Thu Oct 11, 2018 3:40 pm 
Offline

Joined: Mon Oct 25, 2004 10:02 am
Posts: 2865
Location: East Peoria IL
Aaaaaaaahhhhhh the good old days. When a P___y was a P___y!

If I only have millions for them to try and get.


Top
 Profile E-mail  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 84 posts ]  Go to page Previous  1, 2, 3, 4

All times are UTC - 5 hours [ DST ]


Who is online

Registered users: Bing [Bot], Duneit, eseymour72, Garemie, Google [Bot], Lanix, Q, wyeeoddy


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group