PilotOdyssey.com
http://www.pilotodyssey.com/PO/

Seabees son's monster green build.
http://www.pilotodyssey.com/PO/viewtopic.php?f=5&t=17234		 Page 4 of 4
Author:  Randman [ Mon May 29, 2017 10:00 pm ]
Post subject:  Re: Seabees son's monster green build.
As far as blowing into it with just lung pressure the best you're going to do is a bout 1 psi, however your fuel pressure from the pump is going to be around 3 to 5 psi so you can't match the pressure of the pump with your lungs.

You could have a dirty fuel seat. Remove the carb, take the carb bowl off, remove the float and fuel valve then polish the valve seat and the valve plunger by using some polishing compound on the end of a Q-Tip shoved inside a drill.

Rand
Author:  rmesser [ Mon May 29, 2017 10:49 pm ]
Post subject:  Re: Seabees son's monster green build.
Don't do this.

https://m.youtube.com/watch?v=zUObiYd64kw

I think you can find anything on YouTube.
Author:  mcali2 [ Mon May 29, 2017 11:20 pm ]
Post subject:  Re: Seabees son's monster green build.
Thanks, I had checked that. It is solid. still leaking so I'm guessing perhaps the needle is just not able to seal any more. Its running good now.
Author:  rmesser [ Mon May 29, 2017 11:23 pm ]
Post subject:  Re: Seabees son's monster green build.
Randman wrote:
As far as blowing into it with just lung pressure the best you're going to do is a bout 1 psi, however your fuel pressure from the pump is going to be around 3 to 5 psi so you can't match the pressure of the pump with your lungs.

You could have a dirty fuel seat. Remove the carb, take the carb bowl off, remove the float and fuel valve then polish the valve seat and the valve plunger by using some polishing compound on the end of a Q-Tip shoved inside a drill.

Rand


Ya know back in the day, mid 80s, I knew a girl who had a set of lungs that could easily blow 3 to 5 pounds per square inch. Aaaaaaaahhhhhh the good old days. :shock:
Author:  Randman [ Tue May 30, 2017 12:16 am ]
Post subject:  Re: Seabees son's monster green build.
ROFLMAO!!!!!!!!!!!!!! :-)

You knew my old girlfriend too?

Rand
Author:  mcali2 [ Sun Jun 04, 2017 11:37 am ]
Post subject:  Re: Seabees son's monster green build.
Well its almost done. just a few small details. I drove it around the yard but it never did get warmed up enough to have any power to speak of unless the carb is the issue. It fires right up. I still need the police to come do a vin check before i can complete the mounting of the rad.
Author:  mcali2 [ Thu Oct 11, 2018 9:30 am ]
Post subject:  Re: Seabees son's monster green build.
Image

Starting with the bottom section where the springs go. 1 springs, 2 plastic, 3 gasket, middle section, 4 gasket, 5 plastic, 6 gasket and top of pump. does 7 get used or does it go on each side of #2? i was thinking not only due to the need for the plastic to be flat to seal on the spring section.
Author:  canadian oddy [ Thu Oct 11, 2018 1:55 pm ]
Post subject:  Re: Seabees son's monster green build.
rmesser wrote:
Ya know back in the day, mid 80s, I knew a girl who had a set of lungs that could easily blow 3 to 5 pounds per square inch. Aaaaaaaahhhhhh the good old days. :shock:


Watch it !!!!!!
That was over 30yrs ago, so it should be just about time for the Democrats and all your old girl friends to come out of the wood work and accuse you of grabbing them by the P___Y.
Author:  rmesser [ Thu Oct 11, 2018 3:40 pm ]
Post subject:  Re: Seabees son's monster green build.
Aaaaaaaahhhhhh the good old days. When a P___y was a P___y!

If I only have millions for them to try and get.
Page 4 of 4 All times are UTC - 5 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/