PilotOdyssey.com
http://www.pilotodyssey.com/PO/

odyssey#6
http://www.pilotodyssey.com/PO/viewtopic.php?f=5&t=17656
Page 1 of 1

Author:  jknarfal [ Tue Oct 10, 2017 10:44 am ]
Post subject:  odyssey#6

picked this up off of ebay this week. the only picture he had posted was the first one here. unfortunately its not as clean as i had thought. all the tires are junk and its missing the rear caliper and rotor. the Engine was obviously swapped out with some kind of Chinese 4 stroke. the plan is to clean this up for my daughter like we did on the burn project. i recently acquired a 470 rotax sled for practically nothing. so i plan on using that as the power plant for this build. as you see there is a nice long list off obvious issues that will need to be addressed.

Attachments:
22163909_1451890094917949_879102279_o.jpg
22163909_1451890094917949_879102279_o.jpg [ 53.83 KiB | Viewed 1076 times ]
22219544_1454747694632189_1722905389_o.jpg
22219544_1454747694632189_1722905389_o.jpg [ 55.37 KiB | Viewed 1076 times ]
22243798_1454747607965531_1673973455_o.jpg
22243798_1454747607965531_1673973455_o.jpg [ 109.89 KiB | Viewed 1076 times ]
22219513_1454747644632194_1891430527_o.jpg
22219513_1454747644632194_1891430527_o.jpg [ 64.86 KiB | Viewed 1076 times ]
22219144_1454747697965522_1298574847_o.jpg
22219144_1454747697965522_1298574847_o.jpg [ 53.07 KiB | Viewed 1076 times ]
22243556_1454747661298859_1505556371_o.jpg
22243556_1454747661298859_1505556371_o.jpg [ 76.09 KiB | Viewed 1076 times ]

Author:  canadian oddy [ Tue Oct 10, 2017 12:44 pm ]
Post subject:  Re: odyssey#6

The side view of that top cage looks like it has never been rolled.
I bet that frame is square and good.

Author:  jknarfal [ Tue Oct 10, 2017 1:01 pm ]
Post subject:  Re: odyssey#6

The frame looks decent. It doesn't look abused only neglected. They did cut out the section of frame in the Engine bay and crudely reinstalled it.

Author:  canadian oddy [ Tue Oct 10, 2017 1:05 pm ]
Post subject:  Re: odyssey#6

As for your rear caliper I did do some looking a while ago and maybe you could fit one of these somehow.
http://www.wilwood.com/Calipers/Caliper ... %20Caliper
http://www.wilwood.com/Images/Caliper/I ... -cm-lg.jpg

or this one: http://www.wilwood.com/calipers/Caliper ... o=120-9234

I don't see a rotor on that thing so it looks like you will have to cut one your self. I have been looking for years trying to find a replacement for the FL350 rotor and no go. I found one close but they didn't give enough dimensions for me do be sure.

Author:  jknarfal [ Tue Oct 10, 2017 4:02 pm ]
Post subject:  Re: odyssey#6

I may have a caliper I'll have to dig through my stuff. The rotor I may just have some cut out.

Author:  canadian oddy [ Tue Oct 10, 2017 4:23 pm ]
Post subject:  Re: odyssey#6

I see another issue there.
It looks like the faggot drilled out the output shaft on the transmission and then drilled two holes to put bolts through.
Some people shouldn't be allowed to touch tools.
How do the homo's get a job.

If Trump really wants to save America then all he has to do is deport some of these "mechanics" to North Korea so they can build rockets.

Author:  jknarfal [ Tue Oct 10, 2017 4:58 pm ]
Post subject:  Re: odyssey#6

Yes it's got two bolt holes drilled into that shaft. I'll probably just weld them up. I don't think it will be an issue. If it becomes one I'll swap out the shaft. Or I'll make a new shaft to accept the snowmobile driven clutch.

Author:  jknarfal [ Wed Oct 11, 2017 12:04 pm ]
Post subject:  Re: odyssey#6

Unfortunately whoever attempted this Engine swap cut that shaft down to less than an inch long. So I'll need to find a replacement for sure. I'm surprised by some things on this Odyssey. It has rust here and there but just about every nut and bolt were preserved quite nicely. All the cables are here and free. The axles feel tight. No major damage to the frame.

Attachments:
1507737525544-881802245.jpg
1507737525544-881802245.jpg [ 32.87 KiB | Viewed 1014 times ]

Author:  canadian oddy [ Wed Oct 11, 2017 3:06 pm ]
Post subject:  Re: odyssey#6

The "mechanic" needs to be shot with his own poo

Author:  jknarfal [ Wed Oct 11, 2017 3:48 pm ]
Post subject:  Re: odyssey#6

I agree. Whatever drugs he was on must have been good ones. To even think of putting a 125cc 4 stroke in this is completely absurd.

Author:  jknarfal [ Tue Oct 17, 2017 10:50 am ]
Post subject:  Re: odyssey#6

Got a chance to chip away the poo from this thing. I was very surprised to find that every cable was free and functioning properly. And all were accounted for! The frame is extremely straight with very little rust. All the suspension feels tight shocks and axles feel good. Its a great candidate for the rotax. So far I have about $700 into this total.

Attachments:
extfree_132947305293000939.jpg
extfree_132947305293000939.jpg [ 93.11 KiB | Viewed 964 times ]
extfree_9071290145134100806.jpg
extfree_9071290145134100806.jpg [ 69.62 KiB | Viewed 964 times ]
extfree_3513521786427977978.jpg
extfree_3513521786427977978.jpg [ 59.03 KiB | Viewed 964 times ]
IMG_20170929_131437.jpg
IMG_20170929_131437.jpg [ 105.28 KiB | Viewed 964 times ]
IMG_20170929_131442.jpg
IMG_20170929_131442.jpg [ 100.45 KiB | Viewed 964 times ]

Author:  bullnerd [ Tue Oct 17, 2017 11:39 am ]
Post subject:  Re: odyssey#6

Looks like the holes were "drilled" with torch.

Author:  jknarfal [ Tue Oct 17, 2017 12:21 pm ]
Post subject:  Re: odyssey#6

Yea unfortunately the input shaft was cut shorter than I had thought. I'll have to find a replacement

Author:  jknarfal [ Wed Oct 18, 2017 9:56 pm ]
Post subject:  Re: odyssey#6

Got the Engine out and cleaned up.

Attachments:
IMG_20171018_182400.jpg
IMG_20171018_182400.jpg [ 50.92 KiB | Viewed 915 times ]
IMG_20171018_182258.jpg
IMG_20171018_182258.jpg [ 50.89 KiB | Viewed 915 times ]

Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/