PilotOdyssey.com • View topic - Akpilot Fully modified Pilot.

Board index » Pilot's And Odyssey's » Projects » Akpilot's World

All times are UTC - 5 hours [ DST ]

Akpilot Fully modified Pilot.

Page 1 of 1

[ 5 posts ]

Print view

Previous topic | Next topic

Author

Message

hoser

Post subject: Akpilot Fully modified Pilot.

Posted: Tue Oct 25, 2005 4:55 am

Joined: Mon Dec 15, 2003 2:40 pm
Posts: 22617
Location: Chicago

Here are pics Akpilot sent me of his project Pilot.

Attachments:

File comment: This is with the frame fully welded and fresh paint. you can see the gas tank mounts at the bottom of the frame. I added another crossmember and between them there is six gas tank mounts, They are Honda original mounts - had plenty of them lying around

DSC00264.JPg [ 59.49 KiB | Viewed 2159 times ]

File comment: Gas tank fitted to the frame for the last time, it was only the one millionth time in and out. Looking at it on the left the small fill spout is the 2 cycle oil reservoir and the large one on the right is the gas fill spout. The tank holds about 5.5 gal

Dsc00266.jpg [ 110.18 KiB | Viewed 2147 times ]

File comment: Of course the simi-finished product.

Dsc00284.jpg [ 99.01 KiB | Viewed 2076 times ]

File comment: Most of these pictures were taken at one time. This view was for the set up of the rear axles to get spacing. I ordered the RPM box directly from Dan Reberto, and he directed me to Jay Largo for the other things I might need. I sourced Jay for the Axles

Imga0046.jpg [ 69.27 KiB | Viewed 2159 times ]

File comment: From this picture you can see where I cut the frame. I started right infront of the roll bar hoop, I cut diagonally across the pipe leaving the bottom upright with the front of the frame and the roll bar with the back of the frame. I did this for a coup

Imga0047.jpg [ 84.83 KiB | Viewed 2159 times ]

File comment: This shows the Engine mounts through the gas tank. There are 6 Engine mounts, the four on the gas tank and two on the heads that go the base cross bar of the roll cage. I first made the Engine mount, then enclosed them with 3 almost seperate tanks. I r

Imga0048.jpg [ 79.79 KiB | Viewed 2159 times ]

Top

hoser

Post subject:

Posted: Tue Oct 25, 2005 4:57 am

Joined: Mon Dec 15, 2003 2:40 pm
Posts: 22617
Location: Chicago

Some more

Attachments:

File comment: fitment of Crank Shop double pipes in kit form.

Imga0051.jpg [ 75.31 KiB | Viewed 2158 times ]

File comment: I wrapped the pipes in dimond plate to protect me from the header wrap, itchy crap tha header wrap. I wrapped my mod sled with this stuff and each time i do anything I'm scratchin.

Imga0052.jpg [ 89.21 KiB | Viewed 2158 times ]

File comment: side pic.

Imga0053.jpg [ 81.75 KiB | Viewed 2158 times ]

File comment: Tank taking shape

Imga0065.jpg [ 62.85 KiB | Viewed 2158 times ]

File comment: Engine on tank

Imga0066.jpg [ 59.02 KiB | Viewed 2158 times ]

File comment: One saturday I got tired of working on her, and I took pics

Imga0068.jpg [ 87.62 KiB | Viewed 2158 times ]

File comment: Removable frame member for secondary with jack shaft bearing holder. The trans is able to move towards the motor (( Internal Combustion Engine ? )) about 1". It pivots on the front bottom mount, all other trans mounts have slots to slide. This makes for easier belt changes, and to

Imga0069.jpg [ 98.68 KiB | Viewed 2158 times ]

File comment: Battery mount, always hated the battery infront of the secondary - just harder to service, make adjustments. -talking about FL503

Imga0070.jpg [ 86.48 KiB | Viewed 2158 times ]

File comment: Removable frame member

Imga0071.jpg [ 85.93 KiB | Viewed 2158 times ]

File comment: The clamps for the "removable frame member" are the extra clamps from the donor roll cage hoop.

Imga0072.jpg [ 87.77 KiB | Viewed 2158 times ]

Imga0073.jpg [ 87.79 KiB | Viewed 2158 times ]

File comment: Picture of seat in stock position, 4" from the cross bar. In hindsite I didn't need to extend the frame.

Imga0074.jpg [ 91.34 KiB | Viewed 2158 times ]

Top

mudbogger

Post subject:

Posted: Tue Oct 25, 2005 4:52 pm

Joined: Tue Dec 23, 2003 10:31 pm
Posts: 5559
Location: New Jersey

How much did he extend the frame in the rear Hoser?
also what type of gear box is that -is that a quick change gear box or something?

Top

hoser

Post subject:

Posted: Wed Oct 26, 2005 2:02 am

Joined: Mon Dec 15, 2003 2:40 pm
Posts: 22617
Location: Chicago

Update: Akpilot sent me text to put next to each pic take another look it might
answer some questions about his Pilot

Top

mudbogger

Post subject:

Posted: Sun Oct 30, 2005 11:27 am

Joined: Tue Dec 23, 2003 10:31 pm
Posts: 5559
Location: New Jersey

thanks, I see that-well done AKPILOT

Top

Page 1 of 1

[ 5 posts ]

Board index » Pilot's And Odyssey's » Projects » Akpilot's World

All times are UTC - 5 hours [ DST ]

Who is online

Registered users: Bing [Bot], c5racer, Google [Bot]

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:

Login	FAQ
PilotOdyssey.com Chat PilotOdyssey.com Google Search FL400 Parts FL350 Parts FL250 Parts Admin Email