PilotOdyssey.com • View topic - ride

Board index » Pilot's And Odyssey's » Tech Stuff » CSI Central » FL350 Odyssey CSI

All times are UTC - 5 hours [ DST ]

ride_red 350 Cylinder CSI

Page 2 of 2

[ 46 posts ]

Go to page Previous 1, 2

Print view

Previous topic | Next topic

Author

Message

GarlicGreg

Post subject:

Posted: Sun May 02, 2010 11:09 pm

Joined: Sat Nov 27, 2004 7:04 pm
Posts: 138
Location: Gilroy CA

PM sent

Top

Turbotexas

Post subject:

Posted: Sun May 02, 2010 11:43 pm

Joined: Sun Jul 16, 2006 8:46 am
Posts: 5257
Location: Seguin, TX (near San Antonio)

i BOUGHT SOME RINGS OFF FLEA BAY GUY SAID THEY WERE .25 350, BUT THE LAST 3 NUMBERS DON'T MATCH???
I have 13012-VMO-681??? Service honda site went haywire when I typed this in... Anybody have an idea on what these are???

hoser wrote:

First coice would be to see if you can still get the Honda piston.

Here is the honda part numbers, first try to get the .25mm
13012-VM0-305 RING SET, PISTON (0.25)
13102-VM0-315 PISTON (0.25)

If they cant get the .25mm then try to get the .50mm here is the numbers for the piston and ring.
13103-VM0-315 PISTON (0.50)
13013-VM0-305 RING SET, PISTON (0.50)

With either set you get you will also need the wrist pin, wrist pin bearing and the circlips those numbers are below.
13111-KA4-770 PIN, PISTON
91015-KZ3-003 BEARING, CONNECTING ROD SMALL END
90601-430-000 CLIP, PISTON PIN, 1.2X18 (NEED TWO OF THESE)

Top

Ody_Stable

Post subject:

Posted: Mon May 03, 2010 12:03 am

Joined: Wed Dec 24, 2003 12:06 pm
Posts: 1419
Location: San Diego

Turbotexas wrote:

They are 25 over and I believe they were once part of a complete piston, ring, circlips kit. I have a few sets of those myself

Oh, and they do come up on service honda's page, you need to use VM0 "V" "M" "ZERO" not the letter "O" and they're $28.88 a set

Top

ride_red

Post subject:

Posted: Mon May 03, 2010 11:04 am

Joined: Sun Nov 29, 2009 4:24 pm
Posts: 50
Location: Stillwater, OK

Greg said he had a piston, but no rings for me. Would anybody else have what else I need and be willing to sell? Or a complete set either?

JP

Top

Sunblock

Post subject:

Posted: Mon May 03, 2010 9:11 pm

Joined: Sun Apr 27, 2008 5:36 am
Posts: 1346
Location: Benson, NC

theres a set on ebay, not sure what size though

http://cgi.ebay.com/ebaymotors/FL350R-O ... 25562572c9

I have a set for an 80mm piston and they are part number 13012-vmo-003

Top

ride_red

Post subject:

Posted: Thu May 06, 2010 3:40 am

Joined: Sun Nov 29, 2009 4:24 pm
Posts: 50
Location: Stillwater, OK

Hoser, I got a piston set for .25 over...need me to ship that to you as well??

JP

Top

hoser

Post subject:

Posted: Thu May 06, 2010 9:22 am

Joined: Mon Dec 15, 2003 2:40 pm
Posts: 22617
Location: Chicago

ride_red wrote:

Hoser, I got a piston set for .25 over...need me to ship that to you as well??

JP

Yes I need the piston so I can bore the cylinder.

Top

ride_red

Post subject:

Posted: Thu May 06, 2010 12:20 pm

Joined: Sun Nov 29, 2009 4:24 pm
Posts: 50
Location: Stillwater, OK

It should be in today or tomorrow, so I'll ship out ASAP.

Top

ride_red

Post subject:

Posted: Fri May 14, 2010 5:42 am

Joined: Sun Nov 29, 2009 4:24 pm
Posts: 50
Location: Stillwater, OK

Just wanted to double check that the piston came in good health?

Top

hoser

Post subject:

Posted: Fri May 14, 2010 11:28 am

Joined: Mon Dec 15, 2003 2:40 pm
Posts: 22617
Location: Chicago

ride_red wrote:

Just wanted to double check that the piston came in good health?

Yeah its here hopefully I will be putting the finishing touches on it today :-)

Top

ride_red

Post subject:

Posted: Sat May 15, 2010 6:37 am

Joined: Sun Nov 29, 2009 4:24 pm
Posts: 50
Location: Stillwater, OK

Awesome! Thanks for all your help Hoser!

JP

Top

hoser

Post subject:

Posted: Mon May 17, 2010 5:13 pm

Joined: Mon Dec 15, 2003 2:40 pm
Posts: 22617
Location: Chicago

Ok your cylinder is done, their was some really ugly casting flaws on this thing I could not allow them to remain in place choking your Engine every time you run it, so I spent a little time and knocked all them down smooth them out and blended them in, the piston was prepped and I drilled the cooling/lube holes for you.

Attachments:

DSC06447.JPG [ 56.3 KiB | Viewed 15703 times ]

DSC06455.JPG [ 47.47 KiB | Viewed 15703 times ]

Top

hoser

Post subject:

Posted: Mon May 17, 2010 5:17 pm

Joined: Mon Dec 15, 2003 2:40 pm
Posts: 22617
Location: Chicago

Your cylinder bore was not cleaned you will need to clean it, I got out my refillable lubricator and filled it with Engine oil then sprayed the cylinder down good so their is no way it can rust, its a new policy in my shop I am not taking any chances after seeing GarlicGreg's cylinder, that has never happen and I want to ensure it will never happen again, I never did figure out what caused it to rust like that, nothing in my shop is rusting like that either.

Sorry for the mess

PM me your address again I will ship it right out to you.

Attachments:

DSC06473.JPG [ 71.29 KiB | Viewed 15701 times ]

DSC06475.JPG [ 78.08 KiB | Viewed 15701 times ]

DSC06476.JPG [ 61.16 KiB | Viewed 15701 times ]

DSC06477.JPG [ 77.27 KiB | Viewed 15701 times ]

DSC06478.JPG [ 65.17 KiB | Viewed 15701 times ]

Top

ride_red

Post subject:

Posted: Wed May 26, 2010 5:28 pm

Joined: Sun Nov 29, 2009 4:24 pm
Posts: 50
Location: Stillwater, OK

Got it in the mail last week. Looks good! Now I just gotta get some time to work on the damn thing. Shift work sucks!!
Thanks for the help Hoser

Top

hoser

Post subject:

Posted: Wed May 26, 2010 5:58 pm

Joined: Mon Dec 15, 2003 2:40 pm
Posts: 22617
Location: Chicago

ride_red wrote:

Got it in the mail last week. Looks good! Now I just gotta get some time to work on the damn thing. Shift work sucks!!
Thanks for the help Hoser

NP
Be happy your working :-)

been their done that on the shift work gets old fast..

Top

ride_red

Post subject:

Posted: Wed May 26, 2010 9:18 pm

Joined: Sun Nov 29, 2009 4:24 pm
Posts: 50
Location: Stillwater, OK

Turns out the Honda dealer that I ordered my rings from did NOT have any. So if any of you have a set that you didn't use I would buy them from you. I need a set for the Honda .25 over piston.

Top

ride_red

Post subject:

Posted: Wed May 26, 2010 9:30 pm

Joined: Sun Nov 29, 2009 4:24 pm
Posts: 50
Location: Stillwater, OK

Also what gasket setup do you all recomend for the top end? I found a couple auctions on eBay both for vesrah and cometic.

Top

hoser

Post subject:

Posted: Wed May 26, 2010 10:00 pm

Joined: Mon Dec 15, 2003 2:40 pm
Posts: 22617
Location: Chicago

ride_red wrote:

Also what gasket setup do you all recomend for the top end? I found a couple auctions on eBay both for vesrah and cometic.

My preference would be
1. OEM
2. vesrah
3. cometic

Top

Tpreed

Post subject:

Posted: Thu May 27, 2010 2:19 am

Joined: Mon Jun 15, 2009 3:05 am
Posts: 1228
Location: Chicago

GOOD aluminum OEM base gasket!

http://cgi.ebay.com/ebaymotors/honda-fl ... 414fdc517c

Top

ride_red

Post subject:

Posted: Sun Jun 06, 2010 11:02 pm

Joined: Sun Nov 29, 2009 4:24 pm
Posts: 50
Location: Stillwater, OK

Still looking heavily for some .25 rings!! :-)

Top

ride_red

Post subject: Re: ride_red 350 Cylinder CSI

Posted: Mon Sep 17, 2012 10:22 am

Joined: Sun Nov 29, 2009 4:24 pm
Posts: 50
Location: Stillwater, OK

Bump to the topic still in the "For Sale/Wanted" area.

http://www.pilotodyssey.com/PO/viewtopic.php?f=4&t=7354&start=50

Last bumped by hoser on Mon Sep 17, 2012 10:22 am.

Top

Page 2 of 2

[ 46 posts ]

Go to page Previous 1, 2

Board index » Pilot's And Odyssey's » Tech Stuff » CSI Central » FL350 Odyssey CSI

All times are UTC - 5 hours [ DST ]

Who is online

Registered users: Google [Bot], redskinman, socalgii, wyeeoddy

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:

Login	FAQ
PilotOdyssey.com Chat PilotOdyssey.com Google Search FL400 Parts FL350 Parts FL250 Parts Admin Email